Let's Make Robots!

Log in to get help, show off, share and inspire:

wrench_orange.png Your work in progress or a finished robot: Robot project
script_edit.png Write in your own blog: Blog entry
comments.png Discussions and questions: Forum topic
brick.png Show what you are making robots of: Component
lightbulb.png Help others with what you have learned: Tip or walk through
link.png Add a good web shop, a guide or a cool link: Web link
Purpose: having fun (and learn). May be over-ambitious and take some while to complete Specifications so far: Wild Thumper 6WDWild Thumper Controller (motors, … Read more
Based on Raspberry Pi Model A+, moving autonomously, obstacle avoiding, line following, Braitenberg vehicle
NEW: Maze Solver Video Short description: PiBot-A is a small, autonomous robot based on Raspberry Pi Model A+. Varying sensors can be mounted on its front to … Read more
A BiPed is born. Here is the biped I have been working on. It uses 8 MG995 servos, the Veyron 24 Channel servo controller, two 3.7v Lipo batteries and a Windows 8 … Read more
line following robot; running on 72MHz ARM Cortex M4, stm32f303 (pin compatibile with stm32f103); as controll loop pid is used for basic position control; for … Read more
A basic comparison between a new low power microcontroller and an known one produced by the same manufacturer (in progress)
Disclaimer: information stated in this article is for educational purpouses and under review. Not design decisions should be made solely with this information. You … Read more
Walks with a charming limp
I'm working on a simplified design of my quadruped. The new design should be easy to replicate (with a laser cutter or simple hand tools). Another aspect is that it … Read more
bowden modification of prusa mendel i2
    Modding the prusa mendel i2 for a bowden  system     Read more
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License. 2015-03-28 Read more
I have been developing this 5 axis CNC Controller on and off (mostly off) for the last 3 years. I wanted an "all in one" controller that did not depend on a PC to … Read more
TYPE Light Intensity Avoider / Follower, Line follower , Obstacle avoider , Motion sensor , Normal Driving
This is the multibot that is built  as an all purpose robot. The multibot is based on the arduino uno . 1. Arduino Uno 2 Light  intensity Sensor  3 Coloured Line … Read more
The Garden’s Camera based on Raspberry Pi (with motion detection)
Picammory Mark II The Garden’s Camera based on Raspberry Pi (with motion detection) Introduction Read more
I am novice in Java, IOIO and Robotic. This is my First Robot : A car RC with IOIO-OTG Board and L293d to drive Motors Platform : IOIO-OTGBridge H : L293D2 motors … Read more
I have been working a lot lately in color detection and recognition. My RoboServant robot and also RoboTank both use a similar piece of software. RobotTank uses a … Read more
This project started off like many the desire to build and the curiosity to see if it would work. Thanks to both the desire to build and the curiosity the project … Read more
  Hello, As the rules to this site state, “Write the best English you can.” I have prepared this article as such and can only hold on to the desire it’s up … Read more

Note: You can follow some projects some of the time, but you cannot follow all the projects all the time.




Recently collected


line following robot; running on 72MHz ARM Cortex M4, stm32f303 (pin compatibile with stm32f103); as controll loop pid is used for basic position control; for … Read more
Walks with a charming limp
I'm working on a simplified design of my quadruped. The new design should be easy to replicate (with a laser cutter or simple hand tools). Another aspect is that it … Read more
bowden modification of prusa mendel i2
    Modding the prusa mendel i2 for a bowden  system     Read more
I have been working a lot lately in color detection and recognition. My RoboServant robot and also RoboTank both use a similar piece of software. RobotTank uses a … Read more
The Garden’s Camera based on Raspberry Pi (with motion detection)
Picammory Mark II The Garden’s Camera based on Raspberry Pi (with motion detection) Introduction Read more

Leo's LiteCar

It's really not easy for me to start,but I am here!
I'm so happy to find this great place,with so many funny friend and robot!
This is my first project from last years which called “LiteCar” , I wish to program my LC running without Delay(); Feeling with a Light Sensor and Fighting with a "Laser Gun".

Project plan:
1,moving action(WASD) by Computer Operator
2,recording its absolute position
3,feedback and maybe some PID? or Balance Filter?
4,Automode:moving by some prepared positions
5,add some other sensor or what else...

I have been developing this 5 axis CNC Controller on and off (mostly off) for the last 3 years. I wanted an "all in one" controller that did not depend on a PC to … Read more
TYPE Light Intensity Avoider / Follower, Line follower , Obstacle avoider , Motion sensor , Normal Driving
This is the multibot that is built  as an all purpose robot. The multibot is based on the arduino uno . 1. Arduino Uno 2 Light  intensity Sensor  3 Coloured Line … Read more