Let's Make Robots!

Control your motors with L293D

UPDATE

***********************************************************************************************
update 26/4/09
***********************************************************************************************

My 1st instructable  :)

http://www.instructables.com/id/HiTec-Servo-Hack/

***********************************************************************************************
***********************************************************************************************

After long research and trial and error,  I´ve came up to a new walkthrough regarding this nice chip, the L293D.

Each project is one project and each one has its own unique power configurations, so you must be aware of the best battery choice and how to distribute voltage through your robot.

I strongly advice you to read the following articles:

Picking Batteries for your Robot
Once you’ve decided on batteries, how do you regulate the voltage

************************************************

L293D gives you the possibility to control two motors in both directions - datasheet

************************************************

The L293D Circuit:

Basic Implementation:

This is the most basic implementation of the chip.

As you can see, a 5V Voltage Regulator is between the battery and pins 1, 9, 16.

Pin 8 gets power before the VReg, if your motor needs for example 6V you should put 6V directly in this pin, all the other pins should not get more than 5V.

This will work with no problem at all, but if you want to do the right implementation take a look at the next example:

3235657956_b3be2b4f2f.jpg?v=0

3262168342_ae12307934.jpg?v=1240780647

This is the correct Implementation (with the capacitors), and note that pin 8 is feeded by unregulated voltage. This means that if your motors need more than 5V, you should power this pin with that amount of voltage, and the rest of the circuit with 5V.

3235658022_f78495fddd.jpg?v=0
The capacitors stabilize the current.

The same circuit on a breadboard:
3252941552_2f4919475f.jpg?v=1240780044

Soldered on a pcb and ready to go:
3234563157_780312a389.jpg?v=0
3451483356_2fdf26be19.jpg?v=0

3257970545_12de4f710e.jpg?v=0

This is the back of the circuit, click for high resolution photo.

***********************************************************************************************
CODE
***********************************************************************************************

// Use this code to test your motor with the Arduino board:

// if you need PWM, just use the PWM outputs on the Arduino
// and instead of digitalWrite, you should use the analogWrite command

// —————————————————————————  Motors
int motor_left[] = {2, 3};
int motor_right[] = {7, 8};

// ————————————————————————— Setup
void setup() {
Serial.begin(9600);

// Setup motors
int i;
for(i = 0; i < 2; i++){
pinMode(motor_left[i], OUTPUT);
pinMode(motor_right[i], OUTPUT);
}

}

// ————————————————————————— Loop
void loop() {

drive_forward();
delay(1000);
motor_stop();
Serial.println(”1″);

drive_backward();
delay(1000);
motor_stop();
Serial.println(”2″);

turn_left();
delay(1000);
motor_stop();
Serial.println(”3″);

turn_right();
delay(1000);
motor_stop();
Serial.println(”4″);

motor_stop();
delay(1000);
motor_stop();
Serial.println(”5″);
}

// ————————————————————————— Drive

void motor_stop(){
digitalWrite(motor_left[0], LOW);
digitalWrite(motor_left[1], LOW);

digitalWrite(motor_right[0], LOW);
digitalWrite(motor_right[1], LOW);
delay(25);
}

void drive_forward(){
digitalWrite(motor_left[0], HIGH);
digitalWrite(motor_left[1], LOW);

digitalWrite(motor_right[0], HIGH);
digitalWrite(motor_right[1], LOW);
}

void drive_backward(){
digitalWrite(motor_left[0], LOW);
digitalWrite(motor_left[1], HIGH);

digitalWrite(motor_right[0], LOW);
digitalWrite(motor_right[1], HIGH);
}

void turn_left(){
digitalWrite(motor_left[0], LOW);
digitalWrite(motor_left[1], HIGH);

digitalWrite(motor_right[0], HIGH);
digitalWrite(motor_right[1], LOW);
}

void turn_right(){
digitalWrite(motor_left[0], HIGH);
digitalWrite(motor_left[1], LOW);

digitalWrite(motor_right[0], LOW);
digitalWrite(motor_right[1], HIGH);
}

Comment viewing options

Select your preferred way to display the comments and click "Save settings" to activate your changes.
those parts are Terminal Blocks, you can get them in hardware and electronic shops   ;)
thanks, oh and sorry to bug you, but what are those white bits, and how do they plug into the arduino?
I use this "white bits" instead of the male to female headers because they are better connectors. In the photo is the correspondent female bit, and to connect to the arduino pins I use male headers as you can see   :)

2851360643_9df5d9f141.jpg?v=0


what are the female headers for, I cant see where they would come in on the circuit diagram
Looking at the diagram you can see the "Microcontroller PWM Pins", and "Microcontroller Power" - this are the male headers ( in the foto they are the "white bits") and it is where you connect the female headers.

Those are Molex KK connectors.  Commonly used in PCs for fan power connetions (3 pin version).

 

thanks men, I understand your explication. Thanks
I´ve updated pics and text  ;)

Thanks guibot for this tutorial, Also I would add that this works without changes for the SN754410 since it is pin-compatible with the L293D.  I was able to do this in just a few minutes and it sure works better than my pololu controller.  Now I know the h-bridge chip was OK, but the PIC was borked on that one :-/

:-)

The SN754410 is pin compatible with the L293D, yes. But not functionally compatible. It's the equivalent of an L293, not an L293D, since it doesn't have clamp diodes built in.