Let's Make Robots!

finding cheap RC ESC (speed controller)

I love RC ESCs. They are electronic speed controllers that you connect to a servo output on a RC receiver or a micro controller, and they give you full step free control over a big motor in both direction. Most of the ones made for RC cars work in the voltage range 6-8.4Volts, but there are several alternatives for people who plan to run up to 24 volt motors in almost constant stall at a gazzilion amps (read robot war contenders).

But I'm the eternal cheapskate, and wants the cheapest there is.. So far I've found this 


It costs $19 and comes as a kit, so I guess I have to solder it myself. Do any of you know of any cheaper ones?

My wanted specs are:

  • run in both direction (not plane type)
  • for brushed motor (not brushless)
  • cool if it has BEC (can supply regulated power for RC receiver or Microprocessor)
  • without break function (racing ESCs will stop the wheels if you go from full forward to full reverse)
  • really really cheap (since I need 4)
  • around 7Volts (I'm not fuzzy)

Comment viewing options

Select your preferred way to display the comments and click "Save settings" to activate your changes.

Hi Guys,

I have been doing this for a while.

Source code is here https://launchpad.net/brushed

I have converted quite a few of hobbykings controllers. Jump on robowars.org/forum -> under technical chat is the thread. Its pretty long but worth a read if you are really cheap.

This is probably the cheapest one you can convert easily (Avr microcontroller for the moment) https://www.hobbyking.com/hobbyking/store/uh_viewItem.asp?idProduct=15202

However the HK10 is the cheapest one I have done @ $5.15 for their "one time bonus offer", current favourite is the TPY1-25 that controller is fantastic. I am running RS550s on it @ 6S which is so far overspec its not funny and it barely gets warm.




Hey, thx for info! Can you reprogram ESCs with USBasp ? 

Brushed motors have two connections while brushless have three and you cannot use ESC for one type on the other.

If you want reverse you need to look for car or boat esc, not aircraft.

Yea, you cant mix both. Regarding reverse I was talking about a brushed ESC where in the comments they say you cant do reverse on that. Its a shame, because hobbyking has only two brushed ESC and both cant reverse :(

Wow, not so expensive. But that ESP is on the backorder or out of stock :( So the ESP is basically like the L293 motor driver, right?

It's more like a servo electronics board, but for a beefier motor. It takes regular servo signals and converts them linearly to motor speed, 1.5ms signal being motor stopped (you also have a jumper to break the motor or just coast at 1.5ms signal). I have a couple of them and they work perfectly with 12V power window motors. I wanted to make a sun following solar pannel, that's why I bought them. But they are good for robots too.

I have no idea why people don't use HobbyKing for LiPos, servos, ESCs and uBECs, as they have great products at cheap prices! 

Aha, so it is like the L293 motor driver. I assume you can control only 1 DC motor in both directions with PWN siganls, right? Should be easy enough to let the arduino take control of that. What should be the PWN / servo signal voltage? 5V ?

The thing is that my two motors require 5A each, so that I have to buy 5 L293 motor drivers. As I can see it, I can just use 2 ESPs.

Well I almoust bought a LiPo 3x times the price that of  hobbyking at our german online store "Conrad". Pretty sick huh.

Its a shame they only have two brushed ESC and both are out of stock. Damn brushless motors...

Not quite. The control signals are different.

L293 takes a PWM signal of about 2kHs and 2 Direction signals to drive a 600mA motor. For a 0% signal width the motor is stopped and for 100% signal width, the motor is rotationg at full speed. Needs 3 control pins from the microcontroller and a simple 8 bit PWM signal (can work in the background).

An ESC (just like a servo) takes a PWM signal (actually it's called PPM) of 50Hz and the width of the signal determines the direction AND speed of the driven motor. The width of the signal is very low, 10% for full speed reverse and 20% for full speed forward, with 15% for motor stopped. Needs only one microcontroller pin and a 16bit timer for a PWM signal (can also work in the background).

The ESC was designed to work like a servo, to be easily plugged in a RC receiver for a boat, car or airplane.

Oh, and the signal level is 5V, you can use the Arduino Servo library to drive one motor with one ESC, for 2 motors you need 2 ESCs.

Don't worry, they will have them back in stock soon.

Thanks for you time writing it, its very informative.

1. So do I need an extra IC timer for controlling the ESP with an arduino ? Be cause of course I want the PPM signal to be working in the background.

2. So the servo and the ESP both take PPM signals in, right? The output of the ESP is PWN which controls the motor, just like the L293. So the PWN is a similar thing but with a different frequency. Thats makes sence, as you connect both the servo and the ESP in to the RC receiver. Then all the signals you send via the remote are PPMs ?

ps. Missed out RC fun in my childhood (damn consoles), now its time though :D Hobbyking has also nice 40€ gliders wich I might buy. Never flew a RC plane in my life.