Let's Make Robots!

Log in to get help, show off, share and inspire:

wrench_orange.png Your work in progress or a finished robot: Robot project
script_edit.png Write in your own blog: Blog entry
comments.png Discussions and questions: Forum topic
brick.png Show what you are making robots of: Component
lightbulb.png Help others with what you have learned: Tip or walk through
link.png Add a good web shop, a guide or a cool link: Web link
Quick and simple tester for LIPO voltages
This was a quickie project for checking LIPO voltages before parallel charging and can also check individual cell voltages of multi-cell batteries or anything using … Read more
ok so this is the stalled K9 mark Pom, I have a Cubie Truck3 for the main brain so I can run the ROS on it. and that is where it stalled lol I have 4 vex omni … Read more
Sense light levels
This is my first project so it may not be very impressive. This  costed arpund $10 to build however I am in the UK... What the project does: if the light level is … Read more
Description: The purpose of the project is to design a robot that can be controlled by human voice. The first video shows the test of the robot. The second video … Read more

Q

test bed for four wheel drive, and hits everything
    Q is my introduction to four wheel drive rover designed to be used with the picaxe 28x2 shield but any controller with  four motors and four servo's will … Read more
Was in home for a one day holiday. Decided to do something. Was pretty simple to make, with ATMEGA by my side. Video quality isn't so good bcoz i am in a hurry, and … Read more
Allows any Arduino board to accept commands from an IR receiver
Most homes these days have at least 1 infrared remote control for controlling the television. These remote controls can also be used to control robots or even to … Read more
I have seen some great quadruped robots on this site in the past few years and always wanted to build one myself. It became one of the most time-consuming projects … Read more
This is my snow plow bot. It is currently RC but I want to convert it to wireless for internet control.Weighs about 200 pounds. Some Specs: Read more
The robot shown here, which is based on factory parts. The HC-SR04 ultrasonic sensing type distance measuring device used. The sen Read more
Balances on two wheels
This robot is called Wheelee. It is simple inverted pendulum robot made on arduino. Firmware, Matlab model, Android application and some articles are on Github … Read more
Stands guard over the halloween sweets
My youngest son and I go to the local CoderDojo and the next meeting has a Halloween theme so I decided to do something based on Scratch for Arduino. Usually I … Read more
Plot Pictures on a whiteboard
This is a review of the Makeblock XY-Plotter v2.0.. I have got the chance to test the new plotter. Many thanks to Makeblock for the plotter kit and the support … Read more
supports bots while not in use
as it says on the tin, this two piece stand with a loo roll for the height. Read more
This is my first attempt at making a biped robot. As with all other robots I have created in the past I always start off small (Test Bed) and then only after … Read more

Note: You can follow some projects some of the time, but you cannot follow all the projects all the time.




Recently collected


Kirchoffs Voltage Law and Current Law - is there easier math for this?

I think I understand the simple examples for this law, thought the math (algebra) is a bit daunting as its been many many years since high school, and I wasn't very good at it then. The more complex examples make me dizzy.  I have to believe there is an easier way to understand and use this law in my robots circuits. Or is this something that I will rarely use? Is there an easy "rule of thumb"?

Here is an example from the class, not even terribly complex, but seems that way for me.

RoboServant is my newest project that I have been working on. I first started this project by making Sparky the little robot that would roam around the house. … Read more
Robots can be made out of anything... can't they? Mopsey is a friendly bot' made from craft fur and a few electronics - designed for simple interaction. Very … Read more
Expresses emotions, solves problems, artificial consciousness
Virtual robot girl will have human like skills. Human like skills means simply, she will be able to learn like a human, she will be able to express emotions like a … Read more
  This is my first raspberry pi project ever. So I am already quite happy with the results. About the robot: It's a modified RC toy (about 0.5m tall). Beside … Read more

Building strapping

Im not sure what it's called, CTC can you enlighten me? But it's cheap and easy to work with. I've used it on Retro bot for the extra battery holder http://letsmakerobots.com/node/8004 You should be able to get it from you local building supplies store. Easy to bend, and cut it with tin snips.

strap.jpgstrap2.jpgretrostrap.jpg 

Cuts parts in wood, plastic, aluminium
                        I always wanted to be able to do my own parts. So I tought it what time for me to do my own 3 axis CNC :) I wanted to share in … Read more

BoB Jr.

Starting a BoB project after seeing Deshipu's μBoB.

STL Viewer (beta)

Model:
Rotate: |