Let's Make Robots!

Log in to get help, show off, share and inspire:

wrench_orange.png Your work in progress or a finished robot: Robot project
script_edit.png Write in your own blog: Blog entry
comments.png Discussions and questions: Forum topic
brick.png Show what you are making robots of: Component
lightbulb.png Help others with what you have learned: Tip or walk through
link.png Add a good web shop, a guide or a cool link: Web link
General InformationNon Pneumatic Tire / Airless Tire (actually just the wheel), matching tire and hub attachment (for printing the wheel without supports) Some … Read more
Increase torque or reduce noise in DC brushed motors
By default, most Arduino pwm outputs are set to about 490Hz or 980Hz. These frequencies work quite well with small dc brushed motors but can cause unwanted noise or … Read more
(This node will probably float a bit, have lots of work to do on it. My apologies.) I'd been wanting to create a bridge between Arduino and iOS for awhile. Not … Read more
Enjoys the sun, twitches a bit and rolls around in a very lazy way.
I haven't posted in a while mostly because I had undertaken a lot of large, complex (for me) projects and I kept getting discouraged because it didn't go as … Read more
Transmitts music without any wires or links!!
  These two rectangle shaped pieces are emitter and receiver of music.The voice is clear , the transmission is nice and clean!!! I hope you like the peacefull … Read more
Stays there, soaking the sun rays. Buzzes angrily once in a while.
The other guy that came out of my little building session on that weekend. I wanted to make a solar roller but somehow the motors I had were unable to push even … Read more
navigates environments based on plant derived data
Tenax Mundus, is the tenacious treaded prototype plantoid ready to conquer wild territories such as mildly cluttered carpet, and courageously... err safely avoid … Read more
Control any device or robot microcontroller through the serial port using an XBee radio module series 1.
With this remote control no longer each time I have to think which is the system that I have to build my new robot control. Only I have to put a XBee in the new … Read more
There are two robotic eyes that move in horizontal and vertical.
This is a project to be mounted on a robot I'm building. These two robotic eyes, made very little money (just look at the list of materials used) and very easy to … Read more
Serves beer cans (or any other can).
Using a
HeinyBot 2.0, robot waiter in process of construction 100%. Four modes of operation provided. Manual, Static Waiter, Dynamic Waiter and Presentation. In manual mode … Read more
Walk, run, surf ultrasonic, go to the most intense point of light and executes all the moves that you can program sequentially
Using a
Hexapod multifunctional. Eligible 4 different programs running from the command of the television. Program 2 manual mode: Since the command can do to walk forward, … Read more
It's not fully operational at this time.
This is a complete rebuild from v1.x, as you can see. This robot is much larger, and much more complex than v1.x was. I designed the decks using 3D CAD and had them … Read more
W.A.L.T.E.R. is my experimental and learning robot platform and will never be complete.  This is the first robot I built, back in 2006 - W.A.L.T.E.R.. It was named … Read more
It tells you the number of people who entered/left your room based on IR
  I'm using an IR LED an IR sensor and an 8 digits screen to show the number of people. When you go throughlaser the sensor sends a 1 signal to the screen.  this … Read more
Provides Rover 5 chassis with motor drivers, power supply and IR sensors
Introduction: The Explorer PCB was designed specifically for the 2 motor / 2 encoder version of the Rover 5 chassis. The Explorer provides all the basic features … Read more

Note: You can follow some projects some of the time, but you cannot follow all the projects all the time.




Recently collected


Servo problems!

I'm having a lot of problems with the servos I'm using to build a quadruped robot. I should start by mentioning that I bought the servos from Dagu like 4 years ago, BUT most of them had never even been unpacked until recently.

The problems are the following:

This tutorial is still under contruction so please check weekly for updates. I have taken it out of "Draft Mode" because it has a lot of useful information for … Read more
Ok, so I have wanted to build a robot for a while, but school prevented me from starting anything.  At the beginning of this summer I bought a Raspberry Pi to just … Read more

Flash Memory of Arduino Uno

 

Sketch uses 13,308 bytes (41%) of program storage space. Maximum is 32,256 bytes.

Global variables use 2,082 bytes (101%) of dynamic memory, leaving -34 bytes for local variables. Maximum is 2,048 bytes.

processing.app.debug.RunnerException: Not enough memory; see http://www.arduino.cc/en/Guide/Troubleshooting#size for tips on reducing your footprint.

Inspired by RodriBot, by Luismi, I decided to make my own biped. I used the four servos that didn't fry in Kubik (the ones I had there before replacing with bigger … Read more

Looking for a custom built inspection robot

Hello to all the community,

I'm looking for a micro TIR (tactical inspection robot) either tracked or wheeled but tall about 1,7 cm , wifi controlled by pc or android tablet and with cctv camera.

Spinning line follower or maze solver
I've now attached a 3D model in Sketchup. Scamper started as an experimental omni wheel platform. The challenge with omni or mecanum wheels is that you need precise … Read more
Roams, seeks/avoids light, line following, hokey pokey, acts silly
Using a
Lil·li·pu·tian Read more